Spaenaur Catalog 14 - Digital Flipping Catalog

Installation Tools / Data / Spare Parts Outils d'installation / Données / Pièces de rechange

Inch and Metric Pouce et Métrique

AVK PNEUMATIC TOOL SPECIFICATIONS

The tool shown on this page has been specifically designed to install the A-T, A-W, E-L and E-H Series Inserts. Once you have selected the type of insert and thread size required for your application, select the appropriate RPM tool from the chart below.

C

A

G

C

F DIA.

E DIA.

D DIA.

B

DIMENSIONAL DATA / TOOL SET-UP REQUIREMENTS PROPER AIR SUPPLY SET-UP REQUIRES: 90-110 PSI (6.2-7.5 BARS) dynamic (tool running) air pressure at 25 S.C.F.M. Inline oiler/separator 3,000 RPM A B C D DIA. E DIA. WEIGHT LBS . (Kg)

F DIA. MAX.

G

2.55 (1.15) 2.58 (1.17) 3.18 (1.44) 3.25 (1.46)

1.86 (47.24) 1.86 (47.24) 1.86 (47.24) 1.86 (47.24)

4.75 (120.6) 4.75 (120.6) 6.00 (152.4) 6.00 (152.4)

7.75 (196.8) 7.75 (196.8) 9.00 (228.6) 8.37 (212.5)

1.57 (39.87) 1.57 (39.87) 1.57 (39.87) 1.50 (38.10)

1.00 (25.40) 1.00 (25.40) 1.00 (25.40) 1.43 (36.32)

.350 (8.89) .600 (15.24) .625 (15.87) .900 (22.86)

1.3 (33.0) 1.3 (33.0) 1.3 (33.0) NA (NA)

1,500

Air pressure gauge and regulator 5/16 or 7.92 mm minimum hose ID 7.92 mm

600

350

SPECIAL FEATURE—The NPT nose cone design incorporates a special serrated tip that is essential to proper insert installation. T

A

B

C

D

THREAD ADAPTION KIT

AIR TOOL SELECTION / SPARE PARTS

70 - 80 60 - 85 60 - 85 60 - 85 70 - 95 80 - 100 90 - 110 95 - 110 2.4 - 2.7 4.1 - 5.5 4.1 - 5.5 4.8 - 6.5 5.5 - 6.8 6.2 - 7.5 6.2 - 7.5 DYNAMICAIR PRESSURE SETTINGS PSI - BARS

D NOSE CONE

T30NPT6 T30NPT8 C BEARING SET

TA632-087 TA832-087 TA1024-150 TA1032-150 TA420-125 TA518-175 TA616-175 TA813-200 TM3-20 mm TM4-20 mm TM5-25 mm TM6-30 mm TM8-40 mm TM10-45 mm TM12-50 mm B MANDREL 10 PER BAG

A HEX DRIVE

THREAD ADAPTION KIT

COMPLETE TOOL PART NUMBER

THREAD SIZE

TOOL R.P.M

6-32 UNC 8-32 UNC

3000 3000 1500 1500 1500

TNPT30P632 TNPT30P832 TNPT15P1024 TNPT15P1032 TNPT15P420

TNPT632TAK TNPT832TAK TNPT1024TAK TNPT1032TAK TNPT420TAK TNPT518TAK TNPT616TAK TNPT813CTA TNPT350TAK TNPT470TAK TNPT580TAK TNPT610TAK TNPT8125TAK TNPT1015TAK TNPT12175CTA

T29NPT2 T29NPT3 T29NPT4 T29NPT4 T29NPT5 T29NPT6 T29NPT7 T29NPT26 T29NPT8 T29NPT9 T29NPT10 T29NPT11 T29NPT12 T29NPT25 T29NPT27

T77NPT6 T77NPT8

10-24 UNC 10-32 UNF 1/4-20 UNC 5/16-18 UNC 3/8-16 UNC 1/2-13 UNC M3 x 0.5 ISO M4 x 0.7 ISO M5 x 0.8 ISO M6 x 1.0 ISO M8 x 1.25 ISO M10 x 1.50 ISO M12 x 1.75 ISO

T30NPT10 T30NPT10 T30NPT250 T30NPT3125 T30NPT375 T30NPT500 T30NPTM3 T30NPTM4 T30NPTM5 T30NPTM6 T30NPTM8 T32PT10 T30NPT500

T77NPT10 T77NPT10 T77NPT250 T77NPT3125 T77NPT375 T77NPT500 T77NPTM3 T77NPTM4 T77NPTM5 T77NPTM6 T77NPTM8 T77NPT1015 T77NPTM12

600 600 350

TNPT6P518 TNPT6P616 TNPT3P813

This chart designates the tool, spare parts and dynamic (tool running) air pressure requirements for our most popular steel product. Contact a Spaenaur Sales Representative for tool RPM and air pressure settings for aluminum, brass and stainless product.

3000 3000 1500 1500

TNPT30P350 TNPT30P470 TNPT15P580 TNPT15P610 TNPT6P8125 TNPT6P1015 TNPT3P12175

CATALOG 14

600 600 350

PREVENTATIVE MAINTENANCE REQUIREMENTS: NOTE: UNF FINE THREAD COMPONENTS ARE AVAILABLE. The bearing set must be kept in a WET lubricated condition to assure proper tool operation. AVK suggests the use of high temperature grease such as LUBRIPLATE® BRAND 930 AA. The tool mandrel should be inspected for thread wear or damage and replaced. To test the condition of the mandrel, thread an AVK insert onto the mandrel backwards until it touches the knurled nose cone. If any drag is still felt, replace the mandrel with a new socket head cap screw.

C145

AVK ® is a registered trademark of AVIBANK MFG., INC.

P : 1-800-265-8772 F : 1-888-252-6380 www. .com F : 1- 8-252-6380 service@spaenaur. © 2018 Spaenaur Inc. All rights reserved. Catalog may not be reproduced, in whole or in part, without the written permission of Spaenaur Inc. Subject to Catalog Terms and Conditions of Use available at Spaenaur.com and on page TC2 and TC3 at the back of this catalog. © 2018 Spaenaur Inc. Tous droits réservés. Le catalogue ne peut être reproduit, en tout ou en partie, sans l’autorisation écrite de Spaenaur Inc. L’utilisation est soumise aux Conditions d’utilisation du Catalogue disponibles sur Spaenaur.com et à la page TC4 et TC5 à la fin de ce catalogue.

18 Jan 2018