Spaenaur Catalog 14 - Digital Flipping Catalog

Installation Tools / Data / Spare Parts Outils d'installation / Données / Pièces de rechange

Inch and Metric Pouce et Métrique

AVK PNEUMATIC TOOL SPECIFICATIONS - Spaenaur No. 122262N

The tool shown on this page has been specifically designed to install the A-L, A-K, A-H, A-P and A-O Series Inserts. Once you have selected the type of insert and thread size required for your application, select the appropriate RPM tool from the chart below.

C

A

G

C

F DIA.

E DIA.

D DIA.

B

DIMENSIONAL DATA / TOOL SET-UP REQUIREMENTS

PROPER AIR SUPPLY SET-UP REQUIRES: 90-110 PSI ( 6.2-7.5 BARS ) dynamic (tool running) air pressure at 25 S.C.F.M. Inline oiler/separator

Spaenaur No.

WEIGHT LBS . (Kg)

D DIA.

E DIA.

F DIA. MAX.

G

RPM

A B

C

2.55 (1.15) 2.58 (1.17) 3.18 (1.44) 3.18 (1.44) 3.25 (1.46)

1.86 (47.24) 1.86 (47.24) 1.86 (47.24) 1.86 (47.24) 1.86 (47.24)

4.75 (120.6) 4.75 (120.6) 6.00 (152.4) 6.00 (152.4) 5.37 (136.3)

7.75 (196.8) 7.75 (196.8) 9.00 (228.6) 9.00 (228.6) 8.37 (212.5)

1.57 (39.87) 1.57 (39.87) 1.57 (39.87) 1.57 (39.87) 1.50 (38.10)

1.00 (25.40) 1.00 (25.40) 1.00 (25.40) 1.00 (25.40) 1.42 (36.06)

.400 (10.16) .400 (10.16) .500 (12.7) .640 (16.25) .900 (22.86)

1.3 (33.0) 1.3 (33.0) 1.3 (33.0) 1.3 (33.0) NA (NA)

TAA912-30P

3,000

TAA912-15P

1,500

Air pressure gauge and regulator 5/16 or 7.92 mm minimum hose ID 7.92 mm

TAA912-9P

900

TAA912-6P

600

SPECIAL FEATURE—The AKPT nose cone design incorporates a special pilot/serrated tip that is essential to proper insert part number designates this feature

880-A03-1X

350

A

B

C

D

THREAD ADAPTION KIT

AIR TOOL SELECTION / SPARE PARTS

D NOSE CONE

T32PT1 T32PT2 T32PT4 T32PT4 T32PT5 T32PT5 T32PT7 T32PT7 T32PT8 T32PT8 T32PT3 T32PT4 T32PT6 T32PT7 T32PT10 C BEARING SET

TA632-150 TA832-150 TA1024-175 TA1032-175 TA420-150 TA428-150 B MANDREL 10 PER BAG TA518-200 TA524-200 TA616-200 TA624-200 TM4-40 mm TM5-40 mm TM6-40 mm TM8-50 mm TM10-50 mm

A HEX DRIVE

THREAD ADAPTION KIT

THREAD SIZE

TAKPT632TAK TAKPT832TAK TAKPT1024TAK TAKPT1032TAK TAKPT420TAK TAKPT428TAK TAKPT518TAK TAKPT524TAK TAKPT616TAK TAKPT624TAK TAKPT470TAK TAKPT580TAK TAKPT610TAK TAKPT8125TAK TAKPT1015TAK

T29NPT22 T29NPT23 T29NPT4 T29NPT4 T29NPT5 T29NPT5 T29NPT6 T29NPT6 T29NPT7 T29NPT7 T29NPT24 T29NPT10 T29NPT11 T29NPT12 T29NPT25

T77AKPT6 T77AKPT8

6-32 8-32

PREVENTATIVE MAINTENANCE REQUIREMENTS: NOTE: UNF FINE THREAD COMPONENTS ARE AVAILABLE. The bearing set must be kept in a WET lubricated condition to assure proper tool operation. AVK suggests the use of high temperature grease such as LUBRIPLATE® BRAND 930 AA. The tool mandrel should be inspected for thread wear or damage and replaced. To test the condition of the mandrel, thread an AVK insert onto the mandrel backwards until it touches the pilot. If any drag is still felt, replace the mandrel with a new socket head cap screw.

T77AKPT10 T77AKPT10 T77AKPT250 T77AKPT250 T77AKPT3125 T77AKPT3125 T77AKPT375 T77AKPT375 T77AKPT470 T77AKPT580 T77AKPT610 T77AKPT8125 T77AKPT1015

10-24 10-32 1/4-20 1/4-28 5/16-18 5/16-24 3/8-16 3/8-24

This chart designates the tool, spare parts and dynamic (tool running) air pressure requirements for our most popular steel product. Contact a Spaenaur Sales Representative for tool RPM and air pressure settings for aluminum, brass and monel product.

M4 x 0.7 M5 x 0.8 M6 x 1.0 M8 x 1.25 M10 x 1.50

CATALOG 14

C144

AVK ® is a registered trademark of AVIBANK MFG., INC.

P : 1-800-265-8772 F : 1-888-252-6380 www. .com F : 1- 8-252-6380 service@spaenaur © 2018 Spaenaur Inc. All rights reserved. Catalog may not be reproduced, in whole or in part, without the written permission of Spaenaur Inc. Subject to Catalog Terms and Conditions of Use available at Spaenaur.com and on page TC2 and TC3 at the back of this catalog. © 2018 Spaenaur Inc. Tous droits réservés. Le catalogue ne peut être reproduit, en tout ou en partie, sans l’autorisation écrite de Spaenaur Inc. L’utilisation est soumise aux Conditions d’utilisation du Catalogue disponibles sur Spaenaur.com et à la page TC4 et TC5 à la fin de ce catalogue.

18 Jan 2018