Section C

Plug Anchors / Toggle Anchors Chevilles d'ancrage / Ancrages papillons

Inch Pouce

E-Z-ANCOR ® SELF-DRILLING DRYWALL ANCHORS ® A Registered Trade Mark of ITW Canada Inc.

(Length 1-11/16" - Shown Actual Size)

SPAENAUR No. 102-002 PKG QTY. 100

1. Place #2 Phillips screwdriver into re cess of E-Z Ancor.

2. Press into gypsum wallboard while turning the anchor clockwise until it is seated flush with the wall.

C

C

CORROSION RESISTANT... MADE OF LONG-LASTING ZINC MATERIAL. FAST... NO PRE-DRILLING OR HOLE PREPARATION. SAVES TIME AND MONEY. EASY... INSTALLS EASILY WITH #2 PHILLIPS SCREWDRIVER...NO ELECTRIC DRILL OR OTHER TOOLS NECESSARY. ATTACH FIXTURE... WITH #8 A OR AB SCREWS. REMOVABLE... CAN BE EASILY BACKED OUT. SECURE... DEEP THREADS PROVIDE STRONG ENGAGEMENT IN 3/8", 1/2" AND 5/8" WALLBOARD. NEAT... UNIQUE TRI-CUT POINT SELF-DRILLS A CLEAN, SMALL HOLE. BREAKAWAY POINT... POINT CAN BE BROKEN OFF IF CAVITY BEHIND WALL BOARD IS TOO SHALLOW.

3. Place fixture in position over installed E-Z Ancor, and insert screw with #2 Phil lips screwdriver (#8 type A or AB screw is recommended).

4. Tighten fixture in place...threads of screw self-thread securely into the anchor (a minimum of 1" thread en gagement is recommended). Do not overtighten.

E-Z ANCOR ® of High Strength Engineered Plastic

SPAENAUR No. 102-019 PKG QTY. 100

• Completely non-conductive. • Made of Du Pont ZYTEL ® Nylon, one piece.

• Self-drilling, strong engagement in 3/8" to 5/8" wallboard. • Install #6 A or AB screw with #2 Phillips screwdriver or cordless screwdriver using a #2 Phillips bit.

(Length 1-3/8" - Shown Actual size)

SELF-DRILLING TOGGLE BOLT FOR HEAVY DUTY ANCHORING TO DRYWALL

1

E-Z TOGGLE SELF DRILLS!

E-Z-TOGGLE ® (Screw Included)

E

X

B

L E

G G

T O

E

Z

2

3

TURN SCREW TO ENGAGE CLAMP!

Toggle Material: ZINC DIE CAST

E

X

E

X

B

B

G G L E

G G L E

T O

T O

E

Z

E

Z

PLACE FIXTURE INSERT SCREW!

4

FAST... no pre-drilling or hole preparation necessary. Saves time and money. EASY... self-drills with #2 Phillips hand-driven or cordless screwdriver... no electric drill or other tools necessary. SECURE... unique clamping arm replaces both 1/8" and 3/16" winged toggles. STRONG... deep threads at head seat anchor into 3/8", 1/2" and 5/8" wallboard... patented clamp provides strong attachment.

PKG QTY. 50

E

X

B

G G L E

T O

E

Z

CONTINUE TURNING SCREW UNTIL TIGHT!

E-Z-TOGGLE ® TEST DATA

Screw Size #8-18

Drywall Shear (lbs.) Thickness (Toggle from drywall) (Toggle in drywall) 3/8" 67 200 1/2" 84 230 5/8" 148 300 NOTE: The values in the table above are not to be used as design values. The results above are ultimate average values. In all cases, the drywall spalled (failed). The values of Pullout and Shear vary with the inconsistency of the drywall. Drywall will vary in strength due to humidity, age and other factors. The drywall used in the independent lab was tested to ASTM Standards. Pullout (lbs.)

CATALOG 14

Recommended Fixture Thickness

SPAENAUR

Screw Included

No.

102-004 102-005

0" - 1/2" 0" - 1/2"

2-1/8" Phillips Pan Head 2-1/8" Phillips Washer Head

All SPAENAUR numbers are suited to 3/8", 1/2" and 5/8" drywall thickness.

C113

P: 1-800-265-8772 F: 1-888-252-6380 www. F: 1-888-252-6380 service@spaenaur.com © 2018 Spaenaur Inc. All rights reserved. Catalog may not be reproduced, in whole or in part, without the written permission of Spaenaur Inc. Subject to Catalog Terms and Conditions of Use available at Spaenaur.com and on page TC2 and TC3 at the back of this catalog. © 2018 Spaenaur Inc. Tous droits réservés. Le catalogue ne peut être reproduit, en tout ou en partie, sans l’autorisation écrite de Spaenaur Inc. L’utilisation est soumise aux Conditions d’utilisation du Catalogue disponibles sur Spaenaur.com et à la page TC4 et TC5 à la fin de ce catalogue. .com 18 Jan 2018