Section L

Pocket Pull ® Flush Handle Poignée encastrée Pocket Pull

Metric Métrique

Pocket Pull ® Flush Handle • Flush installation • For lifting or pulling • Lifting load transferred directly to panel edge • Single-hole, screw-mount installation

SPAENAUR No. ABS, Black UL94-HB PANEL THICKNESS 1 (.040) MIN. 1.8 (.070) MAX. 097-439 Mfr. #P1-30-101-11

25.5 (1.00)

121.5 (4.78)

Other Panel Thickness Range to 3.3 (.130) available Special Order.

LIFT

Material and Finish

91.5 (3.60)

PULL and CUP: ABS, black. SCREWS: Steel, zinc plated plus bright chromate dip.

64.3 (2.53)

23 (.90)

22.4 (.88)

46.7 (1.84)

Operating Temperature Range: -50 ° C to 60 ° C (-60 ° F to 140 ° F)

NOTE : Installation in a panel thickness less than the maximum for each range allows some movement of the pull.

CUP

123 (4.84)

2.5 (.09) PANEL THICKNESS

Installation 1. Prepare a rectangular opening as shown.

2. Place pull in panel, seating the slot against top of opening.

3. Attach cup to pull and back of panel with two screws (supplied).

114.30 ± 0.25 (4.500 ± .010)

0.7 (.03) R MAX.

+0.2 -0.0 38 (1.500 ± .005)

Maximum recommended tightening torque for mounting screws is 0.5 N•m (5 in.-lbs.)

Lifting, Pulling

Product Strength Guidelines (Distributed Load)

Pushing, Sliding Maximum working load 450 N (100 lbs.) Average ultimate load 670 N (150 lbs.)

millimeter (inch)

Dimensions without tolerances are for reference only.

Maximum working load 1300 N (300 lbs.) Average ultimate load 2700 N (600 lbs.)

L

L

17 (0.65)

127.3 (5.01) larger P2

Matte Finish on these surfaces

Snap-in design • Fast, efficient installation • One-piece design • Com pact envelope • For lifting or pulling • Two sizes • Low Gloss Black ABS Product Strength Guidelines (forces applied as shown) *Based on installation in 1.2 mm (.048 in.) steel panel. Maximum loads limited by panel strength.

82.5 (3.25) smaller P2

TYP. 5.3 (.21)

1.5 (.06)

R

40 (1.58) REF.

35.8 (1.41)

25.5 (1.00)

R 1 (.040) TYP.

1.8 (.07)

Panel Thickness

INSTALLATION

PANEL THICKNESS

SPAENAUR No. Large Small 097-444 097-440 Mfr. #P2-41 097-445 097-441 Mfr. #P2-42 097-446 097-442 Mfr. #P2-43 097-447 097-443 Mfr. #P2-51 Mfr. #P2-52 Mfr. #P2-53

132 ± 0.3 (5.20 ± .01)

Min.

Max.

CATALOG 14

1. Prepare a

87.5 ± 0.3 (3.45 ± .01)

1 (.040)

1.4 (.055)

rectangular opening as shown. 2. Engage edge of opening under flange of pull. 3. Firmly snap in opposite flange with a rocking motion. 30.7 ± 0.15 (1.210 ± .005)

1.4 (.055) 1.8 (.070)

R MAX. 1.5 (.06)

1.8 (.070) 2.1 (.085)

2.1 (.085) 2.5 (.100)

Mfr. #P2-54

Mfr. #P2-44

*Maximum working load = 450 N (100 lbs.) *Average ultimate load = 650 N (150 lbs.)

*Maximum. working load = 1800 N (400 lbs.) *Average. ultimate load = 5300 N (1200 lbs.)

All items on this page PKG QTY. 1

L115

P: 1-800-265-8772 F: 1-888-252-6380 www. F: 1-888-252-6380 service@spaenaur.com © 2018 Spaenaur Inc. All rights reserved. Catalog may not be reproduced, in whole or in part, without the written permission of Spaenaur Inc. Subject to Catalog Terms and Conditions of Use available at Spaenaur.com and on page TC2 and TC3 at the back of this catalog. © 2018 Spaenaur Inc. Tous droits réservés. Le catalogue ne peut être reproduit, en tout ou en partie, sans l’autorisation écrite de Spaenaur Inc. L’utilisation est soumise aux Conditions d’utilisation du Catalogue disponibles sur Spaenaur.com et à la page TC4 et TC5 à la fin de ce catalogue. .com 19 Jan 2018