Section H

Cable Clamps

Inch Pouce

Colliers pour câbles

Lightweight - Insulated For • INDUSTRIAL USE • AIR-CONDITIONING • AUTOMOTIVE • MARINE

All clamps have uniform, 1/32" thick, grey, black or beige Polyvinyl Cushion (Temperature range - 25 ° F to +160 ° F.) and are resistant to gasolines, weathering, wear, and most chemicals.

CUSHION

H

A

1/32"

SECTION A-A ENLARGED

A

OPEN

CLOSED

(All Clamps Furnished "OPEN")

2 HOLES-"M" DIA.

R

T

W

D

APPROX 1/16" PULLDOWN

JOGGLE - TO PROVIDE FLUSH MOUNTING

W 2

X

SPAENAUR No.

Holes to

Pre-

Metal

Tube Tube Hole

Dimensions

End

Galvanized Thick. Width Dia.

Centre Dia.

W

Radius

PKG QTY

H

STEEL

T

W D

H

M 2

X

R

703-003 703-004 703-006 703-007 703-008 703-009 703-010 703-011 703-012 703-013 703-015 703-016 703-018 703-020 703-024 703-028 703-032

.040" .040" .040" .040" .040" .040" .040" .040" .020" .040" .025" .025" .025" .025" .040" .040" .040" .032" .054"

1/2" 1/2" 1/2" 1/2" 1/2" 1/2" 1/2" 1/2" 1/2" 1/2" 1/2" 1/2" 1/2" 1/2" 1/2" 1/2" 1/2" 1/2" 1/2"

3/16"

.455" .486" .517" .548" .580" .611" .642" .673"

.203" .203" .203" .203" .203" .203" .203" .203" .203" .203" .203" .203" .203" .203" .203" .203"

1/4" 1/4" 1/4" 1/4" 1/4" 1/4" 1/4" 1/4" 1/4" 1/4" 1/4" 1/4" 1/4" 1/4" 1/4" 1/4" 1/4" 1/4" 1/4"

7/32" 7/32" 7/32" 7/32" 7/32" 7/32" 7/32" 7/32" 7/32" 7/32" 7/32" 7/32" 7/32" 7/32" 7/32" 7/32" 7/32" 7/32" 7/32"

3/8" 3/8" 3/8" 3/8" 3/8" 3/8" 3/8" 3/8" 3/8" 3/8" 3/8" 3/8" 3/8" 3/8" 3/8" 3/8" 3/8" 3/8" 3/8"

100 100 100 100

1/4"

703-H01-1A

5/16"

3/8"

7/16"

50 50 50 50 50 50 50 50 25 25 25 20 20 10 10

1/2"

9/16"

5/8"

11/16" .705"

3/4"

.736"

13/16" .772"

703-H03-1A

7/8"

.803"

15/16" .835"

1"

.866"

1-1/8" .928" 1-1/4" .991"

1-1/2" 1.116" .203" 1-3/4" 1.248" .203"

2"

1.313" .203"

See also page H25 for more clamps.

All clamps furnished “Open” Three things to watch!

CATALOG 14

1.

To properly inspect a clip or clamp, it should be installed on a bar or tube having an outside diameter equal to that of the tube or cable to be supported.

2.

Closing ends without first inserting tube or bar of proper diameter, holes do not align.

Following this procedure, the bolt holes will align. When the two ends are pulled together to the applicable gap shown on the drawing, all other dimensions will then be within tolerance.

3.

Closing ends without first inserting tube or bar of proper diameter, but forcing holes to align, an elliptical shape results.

H27

P: 1-800-265-8772 F: 1-888-252-6380 www. F: 1-888-252-6380 service@spaenaur.com © 2018 Spaenaur Inc. All rights reserved. Catalog may not be reproduced, in whole or in part, without the written permission of Spaenaur Inc. Subject to Catalog Terms and Conditions of Use available at Spaenaur.com and on page TC2 and TC3 at the back of this catalog. © 2018 Spaenaur Inc. Tous droits réservés. Le catalogue ne peut être reproduit, en tout ou en partie, sans l’autorisation écrite de Spaenaur Inc. L’utilisation est soumise aux Conditions d’utilisation du Catalogue disponibles sur Spaenaur.com et à la page TC4 et TC5 à la fin de ce catalogue. .com 19 JAN 2018